|
|
With
75 feet of 3/8" cable and a 1/3 hp motor, the Mini-Rooter
clears lines from roof-top to basement, including kitchen, bath
and laundry drains. You can do heavier work in 4" lines when
the Mini-Rooter is equipped with a 1/2" cable.
This
inexpensive, light weight machine has lots of time-saving features.
For instance, you can remove the drum in seconds for more portability
or switch to a different diameter cable--with no mess and no lost
time. A distributor tube inside the drum allows you to feed cable
in and out without chucking and releasing the cable every few feet
– so you finish quicker. An optional power cable feed gives you
better feeding and retracting control.
For small drain work, you can order your Mini-Rooter with a “J”
Drum or a Dual Drum for handling smaller, more flexible cables. An
optional Mini-Rooter dolly lets you roll the machine to and from the
job on 8" semi-pneumatic wheels.
Some Mini-Rooter safety features: A foot pedal that uses air pressure
to start and stop the machine, with no electrical wiring between pedal
and motor, a ground fault circuit interrupter, and a high impact plastic
guard covering the motor pulley. |
|
|
|
Mini-Rooter Cutter Set
Catalog # MRCS |
Cutter Name |
Part
Number |
Application |
|
Arrow Head |
AH |
Starting Drill (Gets water flowing) |
|
1-1/2" U-Cutter |
1-1/2 UC |
For cutting and scraping |
|
2" Side Cutter
Blades |
2SCB
|
For cutting and scraping |
|
Boring Gimlet |
BG |
For removing loose objects |
|
Mini-Rooter Units - Complete and Ready to Operate |
| MR-A Includes 50 ft. x 3/8" cable (50EM2) and MRCS Cutter Set. |
| MR-B Includes 75 ft. x 3/8" cable (75EM2) and MRCS
Cutter Set. |
| MR-C Includes 50 ft. x 1/2" cable (50EM3) and MRCS
Cutter Set. |
| MR-D Includes 75 ft. x 1/2" cable (75EM3) and MRCS
Cutter Set. |
| To order with Power Cable Feed, add prefix "P", as
P-MR-A. |
| 220/230 & 240 Volt/50 Hz units are available. |
Mini-Rooter™
Specifications |
Weight:
37
lbs. (17 kg) without cable. |
Dimensions:
18" deep x 12" wide x 19" high (45 cm x 30 cm x 46 cm). |
Drum:
Capacity of 75 ft. of 3/8" or 1/2" Flexicore wire rope center
cable. Integral distributor tube.
|
J-Drum:
Capacity of 50 ft. of 1/4" or 5/16" Flexicore cable. |
Dual Drum:
Capacity of 25 ft. of 1/4" or 5/16" in inner drum.
50 ft. of 5/16" or 35 ft. of 3/8" Flexicore cable in outer drum. |
Cutter Set:
Arrow Head, Boring Gimlet, 2" Side Cutter Blade, 1-1/2" U-Cutter. |
Motor:
1/3 hp, with forward-off-reverse switch, spring- loaded mounting for proper
belt tension. |
Load Speed:
165 rpm. |
Belt Guard:
High impact plastic. |
Power Cable Feed:
Drives 1/2" and 3/8" cables. (Optional) |
Foot Pedal:
Leaves operator's hands free to control cable.
Uses air pressure, so there's no electrical contact between pedal and motor. |
Power
Cord:
10 ft. 3 wire vinyl covered with molded plug.
In-line ground fault circuit interrupter. |
Leather Gloves:
With reinforced palm for hand protection and proper slippage when guiding
cable. |
 |
|
|
SCB.jpg)
