We’ve miniaturized our big machine power cable feed and put it on the Super-Vee to give you feeding speed and convenience you haven’t seen before in a hand-held power drain cleaner.
In tight or awkward places, the Power-Vee is like having an extra hand.
To feed the cable just start the Power-Vee and squeeze the feed lever; to retract it, reverse the motor and squeeze the lever. The feed handles 1/4", 5/16" and 3/8" cables. No adjustment, disassembly, or additional parts required.
Our Dyna-Thrust™ bearing system helps carry the weight of the drum, significantly reducing wear on the motor shaft bearing and extending the life of the tool. Also adding to the Power-Vee’s durability is the heavy-gauge stamped aluminum drum. Of course the cables are Flexicore® – with an integral wire rope center. Nobody makes cables like General
Slide Action Chuck and Cartridge Refill Cables
Cartridge Refill To switch to a different diameter cable (or even connect two 3/8” cables together), you just loosen three screws, pull the front of the drum off the cable, and load another cartridge. Changing takes less than a minute and turns what could be a messy job into a clean one. The tough plastic cartridges are so inexpensive, you’ll probably want to store all of your cables in them.
Heavy gauge wire is coiled around 49 strand wire rope and then heat treated. This cable has unequalled strength and the right amount of flexibility. It’s so tough, it has a one year warranty against defect or breakage.
Flexicore Patent Nos.
2,244,735 and 2,849,870
Handylectric Cutter Set – Catalog #HECS
Arrow Head Starting Drill
Starting Drill (Gets water flowing)
For removing loose objects
Down Head Boring Gimlet
For removing loose objects (Goes down waste, not up stack)
Flexible Spring Arrow Head Cutter
Starting Drill (For sharp turns in small lines)
1-1/4 Side Cutter Blade (2 piece set)
For cutting and scraping
All-purpose Down Head Fitting Can be used with all standard HECS cutters.
Closet Auger Attchment Guides 1/4" or 5/16"cable into bowl.
Carrying Case For Super-Vee, Power-Vee and Handylectric.
The rugged Handy-Stand turns General’s popular and reliable hand-held drain cleaners into practical countertop or floor machines. Ergonomically balanced for maximum stability, the lightweight portable Handy-Stand fits the Super-Vee®, Power-Vee®, and Handylectric™. All three models are ideal for unclogging sinks, tubs, and laundry drains.
The convenient Handy-Stand makes it easier for you to carry your hand-held machine to and from the jobsite. The lift handle doubles as a spare cartridge holder and protects your machine from damage. On the job, the Handy-Stand can be positioned either horizontally or vertically for maximum flexibility.
Power-Vee Units - Complete and Ready to Operate
Power Cable Feed
Variable Speed Motor with Reverse Switch
Quick-Change Cable Cartridge
PV-A-WC with case, 25 ft. x 1/4" (25HE1-DH), 25
ft. x 3/8" (25HE2) cables,
HECS cutter set and one additional cartridge. Boxed Weight 33
PV-B-WC with case, 25 ft. x 1/4" (25HE1-DH), 35 ft.
x 3/8" (35HE2) cables,
HECS cutter set and one additional cartridge. Boxed Weight 36
PV-C-WC with case, 50 ft. x 1/4" (50HE1-DH), 35
ft. x 3/8" (35HE2) cables,
HECS cutter set and one additional cartridge. Boxed Weight 39
PV-D-WC with case, 25 ft. x 5/16" (25HE1-A-DH) cable.
Boxed Weight 27 lbs.
PV-F-WC with case, 25 ft. x 1/4" (25HE1-DH) cable.
Boxed Weight 26 lbs.
To order without case, delete suffix WC, as SV-A.
220/230 & 240 Volt/50 Hz units are available.
BOLD listing denotes the best-selling model.
All ball-bearing, double-insulated, reversible motor with variable speed control; 0 – 500 rpm.
Heavy gauge stamped aluminum with inner drum to prevent cable tangling.
50 ft. of 1/4" or 5/16" cable; 35 ft. of 3/8" cable. All cables are left hand wound and reinforced with a wire rope center.
Arrow Head, Boring Gimlet, Down Head Boring Gimlet, 1-1/4" Side Cutter
Blade, Flexible Arrow Head Cutter