|
|
| 
|
| |
|
This
machine is almost as easy to run as a lawn mower. You push eight or
ten foot cable sections into the line until you reach some resistance.
Then attach the rear cable coupling to the machine, stand behind it,
and turn it on. Watch the cable feed itself into the line. When a
section has run into the drain, attach another one and keep going.
This self-feeding feature also works to pull sections out of the line.
The Model 88 handles jobs up to 200 ft. long in lines from 3"
to 10" diameter. A standard 3/4 hp capacitor motor supplies plenty
of power, and an adjustable safety clutch protects cables and operator
against sudden torque build-ups.
Sections come in two styles: all-purpose Flexichain, which has a chain
center, and the stiffer Proflex, which has a spring center. A chain
assures easier cable retrieving if the Flexichain spring should break.
The inner spring in the Proflex gives it greater stiffness, which
is desirable on long or tough jobs. The outer spring is right-hand
wound for faster self-feeding.
Couplings are shown cables screen (see below). Both types snap together
in a second and are taken apart quickly with a spanner wrench or screwdriver.
With the newer “G" connector, no tension is on the locking
pin when running in reverse, making it a more durable coupling.
Snap on the optional 78L-CDC adapter and you can use 6 ft. x 7/8" cables
(6L78) to clear smaller lines. |
| 
|
| 
Model 88 Units - Complete and Ready to Operate
Includes cable feeding tool. |
| 88-GP Includes ten 10GP Proflex sections with "G"
connectors, and RDCS-G cutter set. |
| 88-GF Includes ten 10GF Flexichain
sections with "G" connectors, and RDCS-G cutter
set. |
| 88-8LP Includes thirteen 8LP Proflex
sections (104 ft.) with "L" connectors, and
RDCS-L cutter set. |
| 88-LP Includes ten 10LP Proflex sections
with "L" connectors, and RDCS-L cutter set. |
| 88-LF Includes ten 10LF Flexichain
sections with "L" connectors, and RDCS-L cutter
set. |
| With 1 hp motor, add prefix "1 HP" as 1HP
88-GP. |
| 220/230 & 240 Volt/50 Hz units are available. |
Model
88™ Specifications |
Weight:
80 lbs. (36 kg) without cables. |
Dimensions:
21" wide x 16" high with handle folded down. (53 cm x 41 cm) |
Motor:
3/4 hp with capacitor and 20 ft. power cord with Ground Fault Circuit Interrupter;
rotates 1-1/4"
diameter cables at 500 rpm. |
Gear Head:
Rugged cast iron body, ball bearings, cut gears. |
Wheels:
10" rubber rear wheels, 6" solid rubber caster wheel. |
Combination Hand
or Foot Operated Power Switch:
Air activated for safety; no electrical connection between motor and switch;
can be used as hand or foot switch. Ten foot air hose. |
Power Switch:
Has an “off” position to de-activate the control switch. |
Adjustable Safety
Clutch:
Factory set at 100 inch pounds. Protected by a tamper- resistant snap-on
cover. |
Folding Handle:
Reduces truck storage space. Flips down in a second but is completely secure
in operating position. |
Cutter Set with
“G” Connectors:
Spear Head, Hook Auger, 2" U-Cutter, 3" Heavy Duty Side Cutter,
3" Heavy Duty Saw Blade,
4" Rotary Saw Blade, Large Retrieving Tool, Coupling Wrench. |
Cutter Set with
“L” Connectors:
Spear Head, Hook Auger, 2" U-Cutter, 3" Heavy Duty Side Cutter,
3" Heavy Duty Saw Blade,
4" Rotary Saw Blade, Large Retrieving Tool, Coupling Wrench. |
Sectional Cables:
Four, Eight and ten foot “Cable Saver” sections come in all
purpose Flexichain® which has a chain center, and a stiffer Proflex®
which has a spring center. Proflex is also available in a heavier duty 5/8”
spring center. Available with ‘G’ or ‘L’ connectors |
|
 |
|
